![]() The first line is for information purposes and shows the program status. In the fert.ġ5 explanation of the screen: each column represents a different fertilizer program. The program calculates, before it runs, the water/fertilizer ratio. The program turns the fertilizer pump on and off in accordance with the desired water/fertilizer ratio. The program calculates the amount of cubic meters needed to irrigate by mul- tiplying the entered irrigation quant.ġ4 3.2.1.4.1.2.4 liter/cubic meter (gallons/thg): relative fertilizing. 3.2.1.3.3 m3/hectares (thg/acre): the irrigation is carried out by volume. Advanced operation the program counts the total amount of water passing through all of the water meters. In order to start a program the program must be made active. Upon leaving the factory all of the programs in the controller are inactive. 3.1.3 accumulation: (151) the right hand side of this screen shows daily and periodical water accumulation and up to 7 different fertilize.ġ2 3.2.1.1 active program: (321#1) – the parameter shown next to the program (on the above screen) defines whether the program is active, inactive or paused. ![]() The date when the valve last irrigated and the actual flow rate are also displayed. ġ1 concurrently in one program apart from when it is a co-valve – see below). In some cases it is necessary to enter a password in order to access the required. The direct access numbers for programming via the controller can be found in brackets next to the relevant headings. The first 20 programs are displayed (see the contro.ġ0 the following different functions and data are explained in accordance with the computer screens. One can see which program is operating, which valve is operating (the first valve only), irrigation status and time remaining. ĩ 2.1.2 current status display: back in the main screen the currently operating programs are displayed on the right side. 2.1.1.3.2.1 select the water unit under the water heading (pressing the cell shows the different options) the options are: 2.1.1.3.2.1.1 mm.Ss - irrigating by time (minutes minutes.Seconds seconds) i.E. 2.1.1 the following operation table screen opens: this table is actually an irrigation program table (each row is an irrigation program and e.Ĩ 2.1.1.3.2 quantity – water unit must be checked first and then the quantity is entered. Click on the “operate” button on the main screen. Basic operation 2.1 operating via the computer: the simplest operation is by using the operation table. 1.3 operating via the computer: the comp.ħ 2. see more information about the irrigation program in the operating section.in addition, the irrigation program contains informative data and definitions (see following sections).1.2.3 the plot: the p.Ħ 1.2.7.3 when: the time the irrigation starts, date, number of cycles etc. It also shows periodic and last day accumulations. Information includes: valve status, the program in which it is programmed, flow rate and date of last irrigation. For instructions on hardware installation p.ĥ want to set the controller according to volume (as opposed to time) it is essential to define the water meters. This manual does not explain the hardware installation of the galileo controller. Ĥ 1.1 using the manual this operating manual is designed to provide basic operating instructions as well as providing definitions for open field programming via the software. 43 3.13) auxiliary (general) outputs: (in the controller: 55). Programs), in which program the valve is currently irrigating (a valve can only irrigate 3. Advanced OperationĢ (the numbers in brackets are the access number in the controller) 1) preface. Their numbers although it is possible to program the valve in an unlimited number of Using the valve (see the irrigation program) (up to 3 programs are displayed sorted by The upper left hand side shows which program is currently The valve set up is described in detail in the set up chapter. Valve icon in order to open the following valve property screen:ģ.1.1 Set Up (Valve’s Constant): the valve set up appears on the lower left hand The properties of this object includes: Set up, information and accumulation. Menu and enter the aforementioned direct access number. (system security) and type the code “0009” (do not press Enter). In order to program the access password, access menu 74 In some cases it is necessary to enter a password in order to access The direct access numbers for programming via the controller can be found in brackets next to The following different functions and data are explained in accordance with the computer screens.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |